Skip to end of metadata
Go to start of metadata

Download PDF Document

2018-07-12

For all Mediatrix units with telephony cards

v. 42.3.986


1 Information to Know Before Starting

Before starting to use these configuration notes, complete the following table to make sure you have the required information to complete the different steps.

Note

These configuration notes can be successfully executed, provided your unit is using the Factory default settings.

Information Value Used in Step
IP address used by your Mediatrix unit to communicate with the Management Interface.
  • If your computer is connected to the Ethernet port meant to be connected to the Local Area Network (LAN), i.e. Eth2 on most devices
USE this value 192.168.0.10 Logging on to the Mediatrix Unit Web Interface
  • If your Mediatrix unit is configured to use a DHCP server, use the DHCP server- provided IP address.
Logging on to the Mediatrix Unit Web Interface
IP address or FQDN of the SIP Registrar Host Configuring the Default Servers
IP address or FQDN of the Proxy Host Configuring the Default Servers
IP address or FQDN of the SIP Proxy Host of Messaging Server Host(if required) Configuring the Default Servers
SIP username and password of each endpoint entry Configuring Endpoint Authentication
Realm used for each endpoint. Configuring Endpoint Authentication

2 Basic SIP Endpoint Registration

This scenario describes how to perform a Basic Sip Endpoint Registration for the Mediatrix units.

For more details on network configuration, refer to the Basic Network Configuration technical bulletin.


2.1 Logging on to the Mediatrix Unit Web Interface

Context

For better performances, it is recommended to use the latest available version of Microsoft Internet Explorer, Google Chrome, or Mozilla Firefox.

Note

You may not be able to log on to the Mediatrix unit Web interface if you are using older browser versions. The computer's network card must be on the same subnet as the Mediatrix unit.

Steps

  1. In your Web browser, enter the IP address used by your Mediatrix unit to communicate with the Web interface.
    • If your computer is connected to the Ethernet port, commonly used to be connected to the Local Area Network (LAN), i.e. ETH2 on most devices, use the 192.168.0.10 IP address.
    • If your Mediatrix unit is configured to use a DHCP server with IPv4, use the provided DHCP server IP address.
  2. Enter public as your username and leave the password field empty.

    Note

    The public username account has administrator rights.

    Note

    You can also use admin as a username and administrator as password.

  3. Click Login.

Result

The Information page of the Web interface is displayed.

Next Step

2.2 Configuring the Default Servers

2.2 Configuring the Default Servers

Before You Start

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Context

In some instances, the configuration of the default servers may already be completed.

Steps

  1. Go to SIP/Servers.
  2. In the Registrar Host field, indicate the server IP address or FQDN to use for this gateway.
  3. In the Proxy Host field, indicate the server IP address or FQDN to use for this gateway.
  4. In the Messaging Server Host field, indicate the server IP address or FQDN to use for this gateway, if needed.
  5. Leave the Outbound Proxy Host field empty, unless specifically instructed to set a value.

    Note

    Setting the address to 0.0.0.0:0 or leaving the field empty disables the outbound proxy host.

  6. Click Apply.
  7. Located at the top of the page, click restart required services.

Result

Next Step

2.3 Configuring the Keep Alive feature

2.3 Configuring the Keep Alive feature

Before You Start

Make sure there is a Default gateway in the Gateway Configuration table under theSIP/Gateways tabs.

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Note

This is not supported by all SIP servers, this feature is not mandatory in most use cases.

Steps

  1. Go to SIP/Servers.
  2. In the Keep-Alive table, complete the fields as required.
  3. If you selected an alternate destination, complete the fields of the Alternate Destination table.

Next Step

2.4 Registering Endpoints to the Default Sip Gateway

2.4 Registering Endpoints to the Default Sip Gateway

Context

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Steps

  1. Go to SIP/Registrations.
  2. In the Endpoints Registration table, from the Register selection list, select Enable for each endpoint to register.
  3. In the Endpoints Registration table, from the Messaging selection list, select Enable for each endpoint to register if a messaging server was set in the Configuring the Default Servers step.
  4. From the Gateway Name selection list, select default for each endpoint to register.
  5. Click Apply and Refresh.

Result

Next Step

2.5 Configuring Endpoint Authentication

2.5 Configuring Endpoint Authentication

Context

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Steps

  1. Go to SIP/Authentication.
  2. Click Edit All Entries located at the bottom of the page.
  3. In the Authentication table, from the Criteria selection list, select Endpoint for all endpoints needing registration.
  4. From the Endpoint selection list, select the related FXS port for each entry.
  5. From the Realm field, enter the provided realm and from the Validate Realm selection list, select Enable. If no Realm was provided, leave the field empty and from the Validate Realm selection list, select Disable.
  6. In the User Name field, enter the SIP user name for each entry.
  7. In the Password field, enter the appropriate password for each entry.
  8. Click Apply and Refresh Registration.

Result

The endpoints will be registered.

Next Step

2.6 Configuring OPTIONS Method Support

2.6 Configuring OPTIONS Method Support

Context

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Note

This step is required if your server is configured to only receive 200 OK.

Note

This is not supported by all SIP servers, this feature is not mandatory in most use cases.

Steps

  1. Go to SIP/Interop.
  2. In the SIP Interop table, from the OPTIONS Method Support selection list, select Always 200 OK.
  3. Click Apply.

Result

The unit will always answer 200 OK to SIP OPTIONS messages received (Keep Alive).

Next Step

2.7 Setting Auto-Routing to Use SIP Usernames

2.7 Setting Auto-Routing to Use SIP Usernames

Context

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Steps

  1. Go to Call Router/Auto-Routing.
  2. From the Auto-Routing selection list, select Enable.
  3. From the Criteria Type selection list, select SIP Username.
  4. Click Apply.

Result


3 Available Documentation

For more details, refer to the Mediatrix Documentation .

4 Copyright Notice

Copyright © 2018 Media5 Corporation.

This document contains information that is proprietary to Media5 Corporation.

Media5 Corporation reserves all rights to this document as well as to the Intellectual Property of the document and the technology and know-how that it includes and represents.

This publication cannot be reproduced, neither in whole nor in part, in any form whatsoever, without written prior approval by Media5 Corporation.

Media5 Corporation reserves the right to revise this publication and make changes at any time and without the obligation to notify any person and/or entity of such revisions and/or changes.