Skip to end of metadata
Go to start of metadata

Download PDF Document

2018-11-13

All models except 4102

v. 43.2.1343


1 Safety Recommendations and Information


1.1 Danger, Warning, Caution, and Note Definitions

Danger

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Warning

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Caution

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury or damage to property or equipment.

Note

Indicates important information not related to personal injury.


1.2 Electrical Safety Guidelines

Danger

Do not work on the Mediatrix unit, connect or disconnect its cables during periods of lightning.

Danger

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Warning

The earth ground cable must be firmly and securely connected to the grounding screw on the back of the Mediatrix unit and an appropriate grounding point in your site: the earth ground cable must remain tightly secured at all times during service and installation.

Warning

Disconnect all interface cables (including PRI,FXS,and FXO) before unplugging any power sources from the Mediatrix unit.

Warning

Disconnect all interface cables (including PRI,FXS,and FXO) as well as all power sources connected to the Mediatrix unit before servicing the unit.

Warning

This equipment must be installed and maintained by service personnel. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous.

Warning

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15 A U.S. (240 VAC, 10 A international) is used on the phase conductors (all current-carrying conductors).

Warning

The unit must be grounded at all times when in use.

Warning

Do not connect the ETH2, ETH1,LAN, and FXS connectors directly to the Public Switched Telephone Network (PSTN), to an off premise application, an out of plant application, any exposed plant application, or to any equipment other than the intended application, connection may result in a safety hazard, and/or defective operation and/or equipment damage. Exposed plant means where any portion of the circuit is subject to accidental contact with electric lighting or power conductors operating at a voltage exceeding 300 V between conductors or is subject to lightning strikes.

Warning

The Mediatrix unit must be installed on a circuit equipped with a breaker so that you can easily power the unit off if required.

Warning

Hazardous network voltages might be present in WAN, LAN, Sync, and telephony port connectors regardless of whether power to the device is OFF or ON. Use caution when working near these connectors to avoid electric shocks.

Warning

The socket outlet, if used, shall be located near the equipment and shall be easily accessible by the user. The AC adaptor inlet is considered as a disconnection device. The device must be readily operational.

Caution

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cords.

Caution

The RJ-11 cable should comply with UL 1863 and CSA C22.2 No 233 standards.


1.3 General Safety Practices

Warning

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

Warning

Do not expose the unit to rain or moisture to avoid any shock hazard.

Warning

Do not use the telephone to report a gas leak in the vicinity of the leak.

Warning

Do not get this product wet or pour liquids into it.

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations.

Caution

Unit main become very hot in case of fan failure or during intensive use. To avoid any accidental burns, it is important to restrict the physical access to the unit, and to shut it down for 30 minutes before touching it. In case of fan failure, please contact Media5 or your authorised reseller or vendor.

  • Keep your Mediatrix unit clear and dust-free during and after installation.
  • Locate the emergency power-off switch for the room in which you are working. Then, if an electrical accident occurs, you can act quickly to turn off the power.
  • Do not work alone if potentially hazardous conditions exist.
  • Never assume that power is disconnected from a circuit. Always check.
  • Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
  • Do not open or disassemble this product.
  • The unit should be located at 20 cm from your monitor, computer casing or other peripheral including speakers.
  • When the unit is brought from a cold to a warm environment, condensation, that might be harmful to the unit, may occur. If this is the case, wait one hour before powering the unit.

1.4 Electrostatic Discharge Prevention

  • When working on a Mediatrix unit, always wear an ESD wrist strap, ensuring that it makes a good contact with your bare skin.
  • Attach the ESD wrist strap end to an earth ground i.e. the grounding screw on the back of the Mediatrix unit or on an unpainted bare metal spot of a grounded equipment rack.

1.5 Translated Warning Definition

Warning

Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, you must be aware of the hazards involved with electrical circuitry and familiar with standard practices for preventing accidents.

Warning

Dit waarschuwingssymbool betekent gevaar. U overtreat in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen.

Warning

Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista.

Warning

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.

Warning

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt

Warning

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti.

Warning

Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.

Warning

Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes..

Warning

Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes.

Warning

Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador.


2 Requirements


2.1 Location Requirements

To avoid premature aging of the unit, insure user security and facilitate access, upgrades and maintenance, the following guidelines must be followed.

  • Install the Mediatrix unit:
    • on a standard 48.26 cm (19 in.) equipment rack
    • on a flat surface (desk, table, etc.)
  • Install the Mediatrix unit in a well-ventilated location where it will not be exposed to high temperatures or humidity.
    • Storage temperature: -20ºC to +70ºC
    • Operating temperature: 0ºC to +40ºC
    • Humidity lower than 85% and non-condensing
  • Do not install the Mediatrix unit in a location exposed to direct sunlight or near stoves or radiators. Excessive heat could damage the internal components.
  • Unit should be positioned to be accessible for future upgrade, maintenance and troubleshooting and where cables can be easily connected.
  • Maintain a minimum of 25 mm (1 in.) clearance in front, in the back, on top, under, and on the sides of the unit.
  • Access to the unit should be restricted to avoid any accidental physical contact, as unit can become very hot.
  • Keep airflow around and through the vents of the unit clear of any obstruction.
  • Do not put books or paper on the unit.

2.2 Wiring Guidelines

These guidelines apply for any cable, supplied or not, used with a Mediatrix unit.

  • Always use straight through cables.
  • Cables must not pull or create a lateral stress on the connectors, i.e. they must be long enough.
  • Cables must be installed in such a way not to present a trip hazard to personnel working in the vicinity of the equipment.
  • Keep cables away from:
    • Sources of electrical noise such as radios, transmitters, and broadband amplifiers
    • Power lines
    • Fluorescent lighting fixtures
    • Liquids or moisture
    • Heat sources

2.3 Mediatrix 4100 Series Characteristics

Parameter Description
Dimensions
  • Height: 4.4 cm (1.74 in.)
  • Width: 43 cm (17.19 in.)
  • Depth: 21 cm (8.4 in.)
Weight
  • 1.7 kg (3.7 lbs)
Power consumption
  • 100 Vac - 240 Vac
  • 50 Hz / 60 Hz 1.6 A

2.4 Power Consumption

Model Voltage /Frequency Operating Conditions Current (mA) Power (W) VA Thermal Dissipation
4108 120 Vac / 60 Hz All ports off hook 226 18 27 17
240 Vac / 50 Hz All ports off hook 176 20 42 19
120 Vac / 60 Hz All ports ringing into 3REN each 306 25 37 15
240 Vac / 50 Hz All ports ringing into 3REN each 233 28 56 18
4116 120 Vac / 60 Hz All ports off hook 368 30 44 28.5
240 Vac / 50 Hz All ports off hook 274 34 66 32.5
120 Vac / 60 Hz All ports ringing into 3REN each 532 43 64 23.5
240 Vac / 50 Hz All ports ringing into 3REN each 341 43 82 23.5
4124 120 Vac / 60 Hz All ports off hook 540 41 65 41
240 Vac / 50 Hz All ports off hook 360 41 86 41
120 Vac / 60 Hz All ports ringing into 3REN each 580 37 70 37
240 Vac / 50 Hz All ports ringing into 3REN each 500 37 120 37

3 Getting Started


3.1 Installation Check List

Task Verified by Date
Network information available and recorded in site log.
Location requirements verified.
Site power Voltage.
Installation site pre-power check completed.
Mounting tools and equipment available.
Additional equipment available.
Mediatrix unit received.
Regulatory compliance and safety information received.
Software version verified
Rack, desktop mounting of chassis completed.
Initial electrical connections established.
Cable length limits verified.
Initial configuration performed.
Initial operation verified.

3.2 Package Check List

Item Condition
1 Mediatrix unit
1 Power cord with the proper model for the country
1 Printed flyer
1 Bumpon kit for desktop use

3.3 Cleaning Instructions

To clean a Mediatrix unit, wipe with a soft dry cloth.

Caution

Do not use volatile liquids such as benzine and thinner as they can damage the unit's casing.

For resistant markings, wet a cloth with a mild detergent, wring well and then wipe off. Use a dry cloth to dry the surface.


3.4 Mounting Tools and Equipment

Tools

  • ESD wrist strap

Equipement

  • RJ-45 cables for the WAN and LAN connections
  • RJ-11 cable for telephony connections (for the 4108 and 4116)
  • RJ-21 cable (only for 4124)

3.5 Connectors and Indicators

LEDs

# LED Behavior Condition
7 Ready Green, steady ON All lines are enabled (operational state)
Green, steady OFF All lines are disabled (operational state)
Blinking 1 cycle per 4 seconds, 75% duty At least one line is enabled and at least one line is disabled (operational state)
8 In-Use OFF Lines idled and unlocked
Steady ON Lines in use and unlocked
Steady yellow Shutting down
Yellow, blinking yellow, 1 cycle per second, 50% duty Locked
9 LAN Green, blinking, variable rate Network traffic
Green, steady ON No network traffic
OFF Not connected
10 Power Amber, steady ON Restart completed
OFF Indicates that the unit is not connected
Blinking, 1 Hz, 50% duty Restart in progress

Switches

# Switch Description
11 Reset/Default Allows setting the unit to default (known) values. Refer to RESET-DEFAULT Button

Connectors and cards

# Connectors/cards Description
1 ETH1 A 10/100 BaseT Ethernet RJ-45 connector for access to a LAN, WAN or computer. This port is by default used for uplink / WAN connection.
2 ETH2 10/100 BaseT Ethernet RJ-45 connector for access to a LAN, WAN or computer. These ports are used by default for LAN connections.
3 FXS connectors Eight RJ-11 connectors to attach conventional telephones or G3 fax machines. These connectors are available on the Mediatrix 4116 only.
4 Analog Lines A RJ21X connector with 24 RJ-11 Teladapt connectors to provide line cord connection to analog phones, faxes and modems. This connector is available on the Mediatrix 4124 only.
5 FXS connectors Eight RJ-11 connectors to attach conventional telephones or G3 fax machines. These connectors are available on the Mediatrix 4108 and Mediatrix 4116 only.
6 Bypass Permits users to make and receive calls even when the Mediatrix 4100 is not operating.
12 Power Internal Switching Mode Power Supply (SMPS) Universal input.

3.6 Bypass Feature (4108-4116-4124 Models)

In the event of a power failure or network failure, the bypass feature allows users to make and receive calls even when the Mediatrix unit is not operating

During normal operation, the direct connection between the FXS 1 and FXS 2 connectors is switched out through commuting relays and both ports resume normal functions. When power is removed from the Mediatrix unit or if the Network is down, a phone/fax used on FXS connector 1 (Mediatrix 4108/4116) or analog line 1 (Mediatrix 4124) is directly connected to the SCN Bypass line. FXS connector 1 (Mediatrix 4108/4116) or analog line 1 (Mediatrix 4124) stays in Bypass connection until:

  • The error conditions have been cleared.
  • The device connected to it is on-hook and a delay has elapsed.
When the power is restored, this automatically removes the Bypass connection; this means that any ongoing call on the Bypass connection is terminated.


4 Installing the Mediatrix Unit

Before You Start

Warning

Before performing this procedure, you must first read and understand the Safety Recommendations listed in this document.

Note

Note or take a picture of your unit's serial number before starting the installation, and place the card stickers of the cards not factory installed. Refer to Locating the Product Serial Number

Steps

  1. Install the unit on a flat surface, in an equipment rack or on the wall. Refer to Installing the Unit on a Flat Surface or Installing the Unit on the Wall
  2. Connect the unit power cord in an appropriate AC electrical outlet.
  3. Connect the Telephony Interface Cables. Refer to Connecting the Telephony Cables .

    Caution

    To prevent damage to the Mediatrix unit, make sure to connect the cables to their proper location on the Mediatrix unit.

  4. Connect the Ethernet Cables. Refer to:
  5. Verify the installation. Refer to Verifying the Installation.

4.1 Installing the Unit on a Flat Surface

Before You Start

Warning

Before performing this procedure, you must first read and understand the Safety Recommendations listed in this document.

Steps

  1. Unpack the unit and go through the Package check list.
  2. Apply the Bumpon™ autoadhesive protective products to the bottom of the unit.

    Note

    This will improve the airflow under the unit.

  3. Install the unit on a flat surface.
  4. Make sure the unit is at 20 cm (8 in.) from your monitor, computer casing, or other peripheral, including speakers.

Next Step

4.3 Connecting the Telephony Cables

4.2 Installing the Unit on the Wall

Before You Start

Important

Before performing this procedure, you must first read and understand the Safety Recommendations listed in this document.

Context

Consider writing down the Product Serial Number on a document easy to access before performing the installation of the unit. Refer to Locating the Product Serial Number

Steps

  1. Unpack the unit and go through the Package check list.
  2. Do not connect any cables to the unit.
  3. Make sure the wall is smooth, flat, dry and sturdy.

    Note

    If necessary, install a 250 mm x 200 mm x 12 mm (10 in. x 8 in. x 0,5 in.) plywood on the wall.

  4. Apply the Bumpon™ autoadhesive protection to the bottom of the unit.

    Note

    This will improve the airflow under the unit.

  5. Position the unit against the wall (plywood).
  6. Mark the position of the screw holes on the wall.
  7. Drill two holes on the markings.
  8. Install a screw in each hole.
  9. Align the screw holes of the unit over the screws installed on the wall, and hang the unit.

Next Step

4.3 Connecting the Telephony Cables

4.3 Connecting the Telephony Cables

Context

Note

To prevent damage to the Mediatrix unit, make sure to connect the cables to their proper location on the Mediatrix unit.

Steps

  1. Wear an ESD wrist strap, ensuring it makes good contact with your bare skin.
  2. Attach the ESD wrist strap end to an earth ground (grounding screw on the back on the Mediatrix unit or unpainted bare metal spot of a grounded equipment rack).
  3. Make sure the unit's power switch is OFF.
  4. Make sure the circuit breakers of AC power sources used to power the Mediatrix unit are OFF.
  5. Make sure the provided AC power cord is connected into the POWER connector located on the back of the Mediatrix unit and in an appropriate AC electrical outlet.
  6. Connect faxes, phones or a PBX to the FXS card.

Next Step

10.0.0.1 Connecting the Mediatrix Unit Using a DHCP Server

4.4 Connecting the Mediatrix Unit Using a DHCP Server

Before You Start

  • Make sure that your network connection is working.
  • You must use an IPv4 Network.
  • The IPv4 Network must have a DHCP server.
  • If your unit does not have an FXS port, or if you do not have access to the DHCP server's logs, then use the Connecting the Mediatrix Unit Using a Static IP Address procedure.

Steps

  1. Wear an ESD wrist strap, ensuring it makes good contact with your bare skin.
  2. Attach the ESD wrist strap end to an earth ground (unpainted bare metal spot of a grounded equipment rack).
  3. Make sure the circuit breakers of AC power sources used to power the Mediatrix unit are OFF.
  4. Make sure the provided power cable is connected to an appropriate AC electrical outlet.
  5. Connect a 10/100 BaseT Ethernet RJ-45 cable into the ETH1 connector of the Mediatrix unit.
  6. Connect the other end of the cable to a router/switch connected to your Network.
  7. Validate the installation.
  8. Turn ON the AC power sources that are used to power the Mediatrix unit at the circuit breaker

    Note

    When the unit is brought from a cold to a warm environment, condensation, that might be harmful to the unit, may occur. If this is the case, wait one hour before connecting the power cord.

  9. If you have an FXS port, dial *#*0 to get the IP address or consult the DHCP server's logs to find out your IP address.

Result

The Power LED on the unit will be flashing when the unit performs a DHCP server query. It will become solid once it successfully gets an IP address from the DHCP server. At this point, you can now use the DHCP server IP address to access your unit's management interface.

4.5 Connecting the Mediatrix Unit Using a Static IP Address

Before You Start

  • Your computer must be set to use the 192.168.0.11 private IP address on subnet 255.255.255.0.
  • You must use an IPv4 Network.
  • Make sure that your network connection is working.

Steps

  1. Wear an ESD wrist strap, ensuring it makes good contact with your bare skin.
  2. Attach the ESD wrist strap end to an earth ground (unpainted bare metal spot of a grounded equipment rack).
  3. Make sure the circuit breakers of AC power sources used to power the Mediatrix unit are OFF.
  4. Make sure the provided power cable is connected an appropriate AC electrical outlet.
  5. Connect a 10/100 BaseT Ethernet RJ-45 cable into the ETH2 Ethernet connector of the Mediatrix unit.
  6. Connect the other end of the cable into your PC.
  7. Validate the installation.
  8. Turn ON the AC power sources that are used to power the Mediatrix unit at the circuit breaker.

    Note

    When the unit is brought from a cold to a warm environment, condensation, that might be harmful to the unit, may occur. If this is the case, wait one hour before connecting the power cord.

Result

You can now use the 192.168.0.10 IP address to access your unit's management interface.

4.6 Verifying the Installation

Steps

  1. Contact the Mediatrix unit via the Web Browser, or go to step 2
    1. In your Web browser, enter the IP address used by your Mediatrix unit to communicate with the Web interface.
    2. Enter public as your username and leave the password field empty.
    3. Click Login.
  2. Contact the Mediatrix unit with an SNMP browser, or
  3. Contact the Mediatrix unit via the CLI, or
  4. Ping the Mediatrix unit.

5 Cables


5.1 10-100 Ethernet Connection (RJ-45)

Caution

Always use standard telecommunication cables with a minimum of 26 AWG wire gauge.

  • Category 5 cables can be used for 10/100 Base T-Connections.
  • It is possible to use either a crossover or a straight Ethernet cable as the Mediatrix units perform automatic MDI/ MDIX detection, meaning that they adapt to the type of cables connected to them. The Auto MDI/ MDIX feature only works when the unit are configured in auto detect mode, which is the default mode.

Pin Name Description TIA/EIA 568A TIA/EIA 568B
1 Bl_DA+/Tx+ Bi-directional pair A+ (Transmit+) white/green white/orange
2 Bl_DA-/Tx- Bi-directional pair A- (Transmit-) green orange
3 Bl_DB+/Rx+ Bi-directional pair B+ (Received+) white/orange white/green
4 not used
5 not used
6 Bl_DB-/Rx- Bi-directional pair B- (Receive -) orange green
7 not used
8 not used

5.2 FXS Connections (RJ-11)

Warning

The RJ-11 cable should comply with UL 1863 and CSA C22.2 No 233 standards.

Caution

Use standard telecommunication cables with a minimum of 26 AWG wire gauge.

Note

The maximum standard FXS cable length is 450 m.

The RJ-11 pair of wires is wired so that pins 3 and 4 are connected to the Ring and Tip, which meets the EIA/TIA-IS 968 and CS-03 Issue 8, Part III requirements.

Pin # Function
1 Not used
2 Not used
3 Ring
4 Tip
5 Not used
6 Not used


5.3 FXS Connections (RJ21X) for Mediatrix 4124 only

Pins 1 (ring) and 26 (tip) of the ribbon connector are considered position 1. Pins 2 (ring) and 27 (tip) are position 2. This pairing continues through 24 pairs.

Line Ring Tip
1(with bypass) pin1 pin26
2 pin2 pin27
3 pin3 pin28
4 pin4 pin29
5 pin5 pin30
6 pin6 pin31
7 pin7 pin32
8 pin8 pin33
9 pin9 pin34
10 pin10 pin35
11 pin11 pin36
12 pin12 pin37
13 pin13 pin38
14 pin14 pin39
15 pin15 pin40
16 pin16 pin41
17 pin17 pin42
18 pin18 pin43
19 pin19 pin44
20 pin20 pin45
21 pin21 pin46
22 pin22 pin47
23 pin23 pin48
24 pin24 pin49

Note

Pins 25 and 50 are not used.


6 Troubleshooting


6.1 Locating the Product Serial Number

Before You Start

Warning

Make sure your unit is powered off.

Steps

  1. Flip the unit. The serial number is located underneath the unit.

    Note

    This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation.

    Designed and assembled in Canada.

    Caution

    Use with internal Ethernet cable only.

    Warning

    Make sure your unit is powered off before flipping it over. Make sure all your cables are well connected.

  2. Flip the unit and power the unit.

6.2 Troubleshooting

Problem Cause
Unable to contact the Management Interface. Wrong Eth port used for the Network configuration (Mediatrix unit on the edge or in the LAN with or without a DHCP server).
Card does not appear in the Management Interface.
  • The card is broken.
  • The unit is broken.
Card appears in the Management interface, but cannot be used (For example, unable to make calls). The card is not configured properly. Refer to the Software Configuration Guide.
Unable to contact the Management Interface via the CLI.
  • CLI service not activated in the configuration.
  • Protocol used to contact the CLI not activated.
Unable to contact the unit via SNMP.
  • SNMP service not activated.
  • Credentials do not grant access.
Unable to make calls, although cards appear in the Management Interface. Hour and date are not synchronized (required by certificates).

6.3 LED Patterns

LED state Description
All LEDs cycling from left to right, individually blinking 1 cycle per second, 33% duty A firmware pack is being downloaded into the unit and written to persistent storage.
All LEDs blinking at 3 cycles per second, 50% duty. One LED out of two has a 180 degree phase. This pattern lasts for 8 seconds. The download of the firmware has failed. After 4 seconds, the unit restarts.
Power and Ready LEDs blinking (synchronized) 1 cycle per second, 75% duty The partial reset is completed.
Power LED blinking, 1 cycle per 4 seconds, 75% duty Triggered when the unit is booting on the recovery bank and no update is pending.
Power LED blinking green 3 cycles per second, 50% duty Waiting for DHCP (IPv4 or IPv6) answer or IPv6 router advertisement or PPPoE connection. No Ip Address configured.
All LEDs blinking green, 3Hz, 50% duty Waiting for DHCP (IPv4 or IPv6) answer or IPv6 router advertisement or PPPoE connection.
Ready LED OFF, all other LEDs cycling from right to left, left to right. The unit tries to download and install a firmware given by the Network Rescue server.

6.4 RESET-DEFAULT Button

The Reset/Default button is a switch that can be used to perform a partial or factory reset while the unit is running.

In other words, the Reset/Default button can be used to:

  • Cancel an action that was started.
  • Revert to known factory settings if the Mediatrix unit refuses to work properly for any reason or the connection to the network is lost.
  • Reconfigure a unit.

The Reset/Default button will generate different actions depending on the amount of time the button is held.

Pressing Time Action Comment LED Pattern
2 to 6 seconds Restarts the Mediatrix unit. No changes are made to the Mediatrix unit settings. Power1 blinking, all other LEDs OFF
7 to 11 seconds Initiates a Partial Reset of the Mediatrix unit. Restarts the unit in a known and static state while keeping most of the configuration unchanged. All LEDs blinking, 1cycle per second, 50% duty
12 to 16 seconds Initiates a Factory Reset of the Mediatrix unit. Reverts the unit back to its default factory settings. All LEDs steady ON
17 seconds and more No action is taken. This is useful if you accidentally pushed the button and do not need and action to be applied. The action is ignored. N/A

6.5 Partial Reset

The partial reset provides a way to contact the Mediatrix unit in a known and static state while keeping most of the configuration unchanged.

A partial reset can be performed at the initial start-up of the Mediatrix unit or on a unit already in use where the configuration was modified in such a way that the user can no longer access the system by the Web page or otherwise. In both cases, the user will access the Rescue Interface with the Rescue Network Interface using either a static IPv4 address (192.168.0.1 ) or an IPv6 Link Local address connection. These connections give access to the Rescue Management Interface where the configuration of a new unit can be completed and where an existing configuration can be modified.

By default the Rescue Network Interface is disabled. When a partial reset is performed, the Rescue network Interface becomes enabled and the "Power" and "Ready" LEDs are blinking at 1Hz with 75% duty and all other LEDs are off. Once the configuration has been modified to solve the problem that required the partial reset, it is important to disable the Rescue Network Interface to make sure that you are no longer working in the Rescue Network Interface.

Performing a partial reset on a new unit will not modify the configuration, as it has not yet been modified to your needs. However, a partial reset performed on a unit already in use will:

  • Rollback Local Firewall settings that are not yet applied.
  • Add a Local Firewall rule to allow complete access to the Rescue interface.
  • Rollback NAT settings that are not yet applied.
  • Add NAT rule to allow complete access to the Rescue interface.
  • Cancel the changes that were being modified but not yet applied to the configuration.
  • Disable any Network Interface in conflict with the Network Rescue Interface.
  • Configure and enable the Rescue Network Interface to:
    • use the link as the default value used by the Uplink Network Interface
    • set the IP address to 192.168.0.1 and the Network Mask to 255.255.255.0.
    • set the IPv6 link-local address on all network links. The IPv6 link-local address can be found underneath the unit.

A partial reset will also modify the following parameters:

Service Parameter Default Value
AAA Users.Password User(s) from profile are restored with their factory password. All other usernames keep their password.
Users.AccessRights User(s) from profile are restored with their factory rights.
ServicesAaaType (table) Each service will be configured to use Local authentication and no accounting mechanism.
CLI EnableTelnet Disable
TelnetPort 23
EnableSsh Enable
SshPort 22
InactivityTimeOut 15
HOC ManagementInterface=Rescue Lan1
SNMP Port 161
Web ServerPort 80
SecureServerPort 443


6.5.1 Performing a Partial Reset

Before You Start

Note

It is not recommended to access the unit on a regular basis through the Rescue Network Interface.

Steps

  1. When the Power LED is steady or blinking rapidly, insert a small unbent paper clip into the hole of the Reset/Default button located on the Mediatrix unit.

    Note

    The Power LED will start blinking.

  2. Wait a few seconds.
  3. When all LEDs are blinking, but before they stop blinking, remove the paper clip.

    Note

    You have between 7 to 11 seconds.

Result

The Rescue Network Interface is displayed when accessing the Management Interface. Several parameters and services are modified, refer to Partial Reset. Do not forget to perform the Disabling the Rescue Interface step.


6.5.2 Disabling the Rescue Interface

Context

By default the Rescue interface is disabled. However, after a partial reset the rescue interface is enabled.

Steps

  1. Go to Management/Misc.
  2. From the Network Interface drop-down menu, select the interface that will be used to manage the unit.

    Important

    If you keep the Rescue Interface selected, you will not be able to get into the management interface after disabling it.

  3. Go to Network/Interfaces.
  4. In the Rescue Interface table, from the Activation selection list, select Disable.
  5. Click Apply.

Result

The unit will be reachable either on the new configured static IP address or on the DHCP .

6.6 Factory Reset

The Factory reset reverts the Mediatrix unit back to its default factory settings.

It deletes the persistent configuration parameters of the unit, including:

  • User files stored in the File service
  • Certificates, except for factory installed ones
  • Log files of the File service

The Factory reset should be performed with the Mediatrix unit connected to a network with access to a DHCP server. If the unit cannot find a DHCP server, it will sent requests indefinitely. A Factory Reset can be triggered either:

  • Directly on the unit. Refer to Performing a Factory Reset.
  • Via the web interface of the Mediatrix unit (Management/Firmware Upgrade).
  • Via the Command Line Interface of the Mediatrix unit by using the fpu.defaultsetting parameter.


6.6.1 Performing a Factory Reset

Context

The Factory reset alters any persistent configuration data of the Mediatrix unit.

Steps

  1. Insert a small, unbent paper clip into the hole of the Reset/Default button, located on the Mediatrix unit.

    Note

    Do not release the Reset/Default button before the LEDs stop blinking and are steadily ON. This can last from 12 to 16 seconds. If you leave the inserted pin longer, no action will be taken which is useful if you accidentally pushed the button and do not need any action to be applied.

  2. Release the paper clip.

Result

All configuration parameters are reset to their default value. The unit can then be contacted via its WAN interface DHCP-provided IP address (ETH1 or WAN on the 4102), or via its LAN interface default IP address 192.168.0.10 (ETH2 or LAN on the 4102).

7 Standards Compliance and Disclaimers


7.1 Supported Standards

Note

The standards compliance of the Mediatrix units are printed on the same sticker as the product serial number.

Category Specification
Agency approvals
  • Anatel
  • European Union
  • CE mark (Declaration of Conformity)
  • CSA
  • FCC
Safety standards
  • UL 60950-1, Second Edition + Amd 1: 2011
  • CAN/CSA-C22.2 No. 60950-1-07 + Amd 1: 2011
  • Anatel Resolution 238: 2000
  • IEC 60950-1: 2005 (2nd Edition) + Amd 1: 2009 (with all national deviations)
Emissions
  • FCC Part 15: 1998 Class B
  • Resolution 442: 2006
  • EN55022 (2006) Class B
  • EN61000-3-2 (2000) Harmonic current emissions
  • EN61000-3-3 (1995) Voltage fluctuations and flicker (with amendment A1)
Immunity EN55024: 1998 including the following (with amendments A1 and A2):
  • EN61000-4-2 (1995), ESD
  • EN61000-4-3 (1996), Radiated RF
  • EN61000-4-4 (1995), Burst Transients
  • EN61000-4-5 (1995), Surge
  • EN61000-4-6 (1996), Conducted RF
  • EN61000-4-11 (1995), Voltage Dips and Interruptions
Telecom
  • FCC Part 68: Subpart D, January 31, 2001
  • Industry Canada (CS-03, Issue 9, November 15, 2004)

Note

Changes or modifications to your Equipment not expressly approved by Media5 voids the user’s warranty. This device complies with Part 15 of the FCC Rules and RSS-213 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and RSS-213 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help


7.2 Disclaimers

Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/television technician for help.

Important

Any modifications made to this device that are not approved by Media5 Corporation may void the authority granted to the user by the FCC to operate this equipment.

Innovation, Science and Economic Development Canada (ISED)

This Class A digital apparatus complies with Canadian ICES-003.

CE Marking

DECLARATION OF CONFORMITY
We, Media5 Corporation, located at 4229 Garlock st. Sherbrooke, Québec, Canada J1L 2C8, declare that for the hereinafter mentioned product the presumption of conformity with the applicable essential requirements of Directives 2014/30/EC and 2014/35/EC European parliament (EMC and LVD directives)is given. Any unauthorized modification of the product voids this declaration. For a copy of the original signed Declaration Of Conformity please contact Media5 at the above address.

RoHS Declaration Of Compliance

This Mediatrix unit is in compliance with the Council Directives 2011/65/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

RoHS China

Model M complies with the China IEC 60950-1 safety deviation, but does not have CCC approvals.

Altitude of Operation

Use only at altitudes no more than 2000 m above sea level.
Only use in non-tropical climate regions.

8 Product Disposal Instructions

This symbol indicates that the product is classified as electrical or electronic equipment and should not be disposed of along with commercial or household waste at the end of its working life. For appropriate disposal and recycling instructions, contact your local Media5 Corporation provider.
The Waste of Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) was established by the European Union to minimize negative impact on the environment, control hazardous substances, and curtail landfill expansion by using the best available recovery and recycling techniques.


9 Documentation

Mediatrix units are supplied with an exhaustive set of documentation.

Mediatrix user documentation is available on the Documentation Portal .

Several types of documents were created to clearly present the information you are looking for. Our documentation includes:

  • Release notes: Generated at each GA release, this document includes the known and solved issues of the software. It also outlines the changes and the new features the release includes.
  • Configuration notes: These documents are created to facilitate the configuration of a specific use case. They address a configuration aspect we consider that most users will need to perform. However, in some cases, a configuration note is created after receiving a question from a customer. They provide standard step-by-step procedures detailing the values of the parameters to use. They provide a means of validation and present some conceptual information. The configuration notes are specifically created to guide the user through an aspect of the configuration.
  • Technical bulletins: These documents are created to facilitate the configuration of a specific technical action, such as performing a firmware upgrade.
  • Hardware installation guide: They provide the detailed procedure on how to safely and adequately install the unit. It provides information on card installation, cable connections, and how to access for the first time the Management interface.
  • User guide: The user guide explains how to customise to your needs the configuration of the unit. Although this document is task oriented, it provides conceptual information to help the user understand the purpose and impact of each task. The User Guide will provide information such as where and how TR-069 can be configured in the Management Interface, how to set firewalls, or how to use the CLI to configure parameters that are not available in the Management Interface.
  • Reference guide: This exhaustive document has been created for advanced users. It includes a description of all the parameters used by all the services of the Mediatrix units. You will find, for example, scripts to configure a specific parameter, notification messages sent by a service, or an action description used to create Rulesets. This document includes reference information such as a dictionary, and it does not include any step-by-step procedures.


10 Copyright Notice

Copyright ™ © 2018 Media5 Corporation.

This document contains information proprietary to Media5 Corporation.

Media5 Corporation reserves all rights to this document as well as to the Intellectual Property of the document and the technology and know-how that it includes and represents.

This publication cannot be reproduced, neither in whole nor in part, in any form whatsoever, without written prior approval by Media5 Corporation.

Media5 Corporation reserves the right to revise this publication and make changes at any time and without the obligation to notify any person and/or entity of such revisions and/or changes.