Skip to end of metadata
Go to start of metadata

Download PDF Document

2018-05-11

For Mediatrix C710, C711, and 4102S Gateways

v. 42.1.857


1 Requirements

  • Minimum supported 3CX version: 3CX v15 SP4
  • Minimum DGW supported Firmware version: Dgw2.0.30.555
  • You must first download the 3CX templates from 3CX integration templates for your specific unit:
    • Mediatrix 4102S : Mediatrix_4102S_FXS_2.fxs
    • Mediatrix C710: Mediatrix_C710_FXS_4.fxs
    • Mediatrix C711: Mediatrix_C711_FXS_8.fxs

Dgw2.0 firmware can be downloaded from Media5 Support Portal. If you do not have an account to access Media5 Support Portal, please contact your Mediatrix product dealer or Media5 TAC if you have an SLA contract.


2 Information to Know Before Starting

Before starting to use these configuration notes, complete the following table to make sure you have the required information to complete the different steps.

Note

These configuration notes can be successfully executed, provided your unit is using the Factory default settings.

Information Value Used in Step
IP address used by your Mediatrix unit to communicate with the Management Interface.
  • If your computer is connected to the Ethernet port meant to be connected to the Local Area Network (LAN), i.e. Eth2 on most devices
USE this value 192.168.0.10 Logging on to the Mediatrix Unit Web Interface
  • If your Mediatrix unit is configured to use a DHCP server, use the DHCP server- provided IP address.
Logging on to the Mediatrix Unit Web Interface
  • If your Mediatrix unit is configured to use the IPv6 Link Local
Locate the IP Link Local label underneath your Mediatrix unit. Logging on to the Mediatrix Unit Web Interface
Port number used Exporting the 3CX Configuration Script to your PC
MAC address of the Mediatrix unit Exporting the 3CX Configuration Script to your PC
Name of your Mediatrix unit Exporting the 3CX Configuration Script to your PC

3 Configuration on the 3CX Server Side


3.1 Installing the Mediatrix Gateway Templates on the 3CX Server

Before You Start

Templates must first be downloaded from our documentation portal at the following link: 3CX integration templates

Steps

  1. If 3CX was installed using the default settings and folder, go to C:\ProgramData\3CX\Instance1\Data\Http\Templates\fxs, either way locate the 3CX templates folder in your system and open it.
  2. Copy the Mediatrix gateway templates in the fxs folder.
  3. Click CTRL + F5 to refresh your browser.
    the first

    Note

    You do not need to restart the 3CX server.

Result

The Mediatrix devices will then appear in the FXS/DECT gateway selection list.

Next Step

3.2 Adding the Mediatrix FXS Gateway to the 3CX Server

3.2 Adding the Mediatrix FXS Gateway to the 3CX Server

Steps

  1. In the 3CX Web interface, click FXS/DECT, located on the left-hand side of the window.
  2. In the FXS/DECT section, click + Add FXS/DECT.
  3. In the Add FXS/DECT dialog box, from the Select Brand selection list, choose Mediatrix.
  4. From the Select model/device selection list, choose your unit model.
  5. In the MAC Address field, enter the MAC address of your Mediatrix unit.

    Note

    To locate your MAC address, refer to Locating the MAC Address of Your Mediatrix Unit.

  6. Click OK.

Result

Next Step

3.3 Configuring the FXS Mediatrix Gateway in 3CX

3.2.1 Locating the MAC Address of Your Mediatrix Unit

Context

The MAC address of the unit is:

  • printed on a label located under the Mediatrix unit
  • displayed in the Current Status table of the Web Interface (System/Information)


3.3 Configuring the FXS Mediatrix Gateway in 3CX

Before You Start

The Adding the Mediatrix FXS Gateway to the 3CX Server step must be completed.

Context

Steps

  1. In the 3CX Web interface, in the FXS GW dialog box, under the General tab, in the Enter name of Device, type the name of the Mediatrix device.
  2. From the Tone Set Selection selection list, chose your location.
  3. In the Fax Transmission Mode, enter either T.38 or G.711 clear channel according to your configuration.
  4. Select the Extension tab.
  5. In the first field, enter an extension number for the first FXS port.
  6. In the next field, enter an extension number for the next FXS port.
  7. Repeat the previous step for all FXS ports used.

    Important

    Every single port must have a legitimate extension number (not Empty), otherwise the configuration script will not be generated which is the normal behavior of the 3CX server.

  8. Click OK.

Result

The provisioning Link is automatically populated.

Next Step

3.4 Exporting the 3CX Configuration Script to your PC

3.4 Exporting the 3CX Configuration Script to your PC

Before You Start

The Configuring the FXS Mediatrix Gateway in 3CX step must be completed.

Steps

  1. In the General tab, click the link located in the Provisioning Link field.

Result

The file is saved locally on the PC in the Web browser's download folder.

Next Step

4.1 Logging on to the Mediatrix Unit Web Interface

4 Configuration on the Mediatrix Unit Side


4.1 Logging on to the Mediatrix Unit Web Interface

Context

For better performances, it is recommended to use the latest available version of Microsoft Internet Explorer, Google Chrome, or Mozilla Firefox.

Note

You may not be able to log on to the Mediatrix unit Web interface if you are using older browser versions. The computer's network card must be on the same subnet as the Mediatrix unit.

Steps

  1. In your Web browser, enter the IP address used by your Mediatrix unit to communicate with the Web interface.
    • If your computer is connected to the Ethernet port, commonly used to be connected to the Local Area Network (LAN), i.e. ETH2 on most devices, use the 192.168.0.10 IP address.
    • If your Mediatrix unit is configured to use a DHCP server with IPv4, use the provided DHCP server IP address.
  2. Enter public as your username and leave the password field empty.

    Note

    The public username account has administrator rights.

    Note

    You can also use admin as a username and administrator as password.

  3. Click Login.

Result

The Information page of the Web interface is displayed.

Next Step

6.0.0.1 Configuring the Uplink Network Interface

4.2 Configuring the Uplink Network Interface

Context

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Steps

  1. Go to Network/Interfaces.
  2. In the Network Interface Configuration table, from the Link selection list located next to Uplink, leave the default value.

    Note

    The default value for your unit type is listed in Link Default Values for the Uplink Network Interface.

  3. From the Type selection list, select IpStatic (IPv4 Static).

    Note

    The Uplink Network Interface must be set with a fixed public IP address for the NAT/router to be able to do port-forwarding to the unit. It will also be easier for the PBX to communicate with the unit if the address is static.

  4. In the Static IP Address field enter the Uplink static IP address.
  5. From the Activation selection list, select Enable.
  6. Click Apply to apply all changes to the configuration.

    Note

    Once the changes are applied, the connection with the unit might be lost. You may need to reconnect to the Web page using the new address.

Result

The unit can be reached (via the Web) with the Uplink static IP address.

4.2.1 Link Default Values for the Uplink Network Interface

Unit Type Link Default Value
Sentinel 400 eth1
Sentinel 100 eth1
Mediatrix G7 eth1
Mediatrix S7 eth1
Mediatrix C7 series eth1
Mediatrix 3000 eth5
Mediatrix 4104 eth1/eth
Mediatrix 4108/16/24 eth1/Ethernet
Mediatrix 4102 Wan
Mediatrix 4400 series eth1/Network
Mediatrix LP series eth1/Ethernet
Mediatrix 4108 IPPBX eth1/Ethernet

4.3 Setting the Uplink Network Interface to a Static Address

Context

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Steps

  1. Go to Network/Interfaces.
  2. In the Network Interface Configuration table, from the Link selection list located next to Uplink, select eth1.
  3. From the Type selection list, select IpStatic (IPv4 Static)IpDhcp (IPv4 DHCP) or PppIpcp (IPv4 PPPoE)
  4. In the Static IP Address field, enter the static IP address as defined in your network address range.

    Note

    The Uplink Network Interface must be set with a static public IP address for the NAT/router to be able to do port-forwarding to the unit. It will also be easier for the PBX to communicate with the unit if the address is static.

  5. In the Static Default Router field, enter the IP address of the router or of the NAT/FW located in the LAN.
  6. From the Activation selection list, select Enable.
  7. Click Apply to apply all changes to the configuration.

Result

The unit can be reached (via the web) with the Static Address.

Next Step

4.4 Connecting the Mediatrix Unit to the Network

4.4 Connecting the Mediatrix Unit to the Network

Steps

  1. Connect a 10/100 BaseT Ethernet RJ-45 cable in the ETH1 port of the Mediatrix unit.
  2. Connect the other end of the 10/100 BaseT Ethernet RJ-45 cable to the Network.

Next Step

4.5 Importing a Configuration Script from Your PC

4.5 Importing a Configuration Script from Your PC

Context

If you are not familiar with the meaning of the fields and buttons, click Show Help, located at the upper right corner of the Web page. When activated, the fields and buttons that offer online help will change to green and if you hover over them, the description will be displayed.

Steps

  1. Go to Management/Configuration Scripts.
  2. If you are not using HTTPS, click Activate unsecure file transfer through web browser.
  3. In the Transfer Scripts Through Web Browser table, browse to the location of the file you wish to import.
  4. If the file is encrypted, complete the Privacy Key field.

    Note

    The privacy key must match the privacy key used to encrypt the file.

  5. Click Upload and Execute.
  6. Located at the top of the page, click Refresh.

Result

The configuration script will be imported from your PC and any changes to the script will be applied to the running configuration.

Next Step

4.6 Checking the Port Registration Status

4.6 Checking the Port Registration Status

Steps

  1. In the DGW Web Interface, go to SIP/Registration
  2. In the Registrations page, check in the Status column if all ports are Registered.

Result

At this point you can test calls. Refer to the Testing Telephony Services technical bulletin at https://documentation.media5corp.com/ .

5 Documentation

Mediatrix units are supplied with an exhaustive set of documentation.

Mediatrix user documentation is available on the Documentation Portal .

Several types of documents were created to clearly present the information you are looking for. Our documentation includes:

  • Release notes: Generated at each GA release, this document includes the known and solved issues of the software. It also outlines the changes and the new features the release includes.
  • Configuration notes: These documents are created to facilitate the configuration of a specific use case. They address a configuration aspect we consider that most users will need to perform. However, in some cases, a configuration note is created after receiving a question from a customer. They provide standard step-by-step procedures detailing the values of the parameters to use. They provide a means of validation and present some conceptual information. The configuration notes are specifically created to guide the user through an aspect of the configuration.
  • Technical bulletins: These documents are created to facilitate the configuration of a specific technical action, such as performing a firmware upgrade.
  • Hardware installation guide: They provide the detailed procedure on how to safely and adequately install the unit. It provides information on card installation, cable connections, and how to access for the first time the Management interface.
  • User guide: The user guide explains how to customise to your needs the configuration of the unit. Although this document is task oriented, it provides conceptual information to help the user understand the purpose and impact of each task. The User Guide will provide information such as where and how TR-069 can be configured in the Management Interface, how to set firewalls, or how to use the CLI to configure parameters that are not available in the Management Interface.
  • Reference guide: This exhaustive document has been created for advanced users. It includes a description of all the parameters used by all the services of the Mediatrix units. You will find, for example, scripts to configure a specific parameter, notification messages sent by a service, or an action description used to create Rulesets. This document includes reference information such as a dictionary, and it does not include any step-by-step procedures.


6 Copyright Notice

Copyright © 2018 Media5 Corporation.

This document contains information that is proprietary to Media5 Corporation.

Media5 Corporation reserves all rights to this document as well as to the Intellectual Property of the document and the technology and know-how that it includes and represents.

This publication cannot be reproduced, neither in whole nor in part, in any form whatsoever, without written prior approval by Media5 Corporation.

Media5 Corporation reserves the right to revise this publication and make changes at any time and without the obligation to notify any person and/or entity of such revisions and/or changes.