Available DGW Firmware Versions
The firmware pack is a binary file that contains the modules and the features to install on your Mediatrix unit when a new release is available.
Incident # | CR # | Synopsis | Applies To |
---|---|---|---|
Description | |||
--- | DGW-8324 | Add the Image Format parameter for the creation of a virtual machine (VM) | Vm |
The Image Format parameter allows the user to choose a VM image format when creating a VM image. The new parameter is available in the DGW Web interface under System/VM in the Virtual Machine Creation table. Possible values are:
|
|||
--- | DGW-8173 | New versioning schematic of DGW 2.0 application. | all |
The DGW 2.0 application is renamed DGW. Refer to the DGW Software Numbering Convention technical bulletin published on our documentation portal. |
|||
--- | DGW-8090 | Add the possibility for the Vm service to convert an existing VM image from a file format to another (QCOW2 or RAW). | Vm |
The "Vm.ConvertVmImage" command allows to convert an existing VM image into QCOW2 or RAW file format. The command can also compress the VM image and remove the existing image following the creation of the new converted VM image file. |
|||
--- | DGW-8069 | Virtual machines (VM) should be properly shut down before restarting the Mediatrix unit. | Vm |
When the Mediatrix unit is shut down, then a process now allows the unit to properly close the virtual machines. The new Vm.ShutdownTimeout parameter was added to configure the maximum amount of time allowed for a VM to stop. this parameter is not available in the DGW Web page. |
Incident # | CR # | Synopsis | Applies To |
---|---|---|---|
Description | |||
IN-13236 |
DGW-8444 | Unable to select the transport protocol in a Call Agent via the DGW Web page when a gateway is selected. | Sbc |
The configuration of the Force Transport parameter via the Web page for a Call Agent will be enabled at all times. |
|||
--- | DGW-8324 | Add the Image Format parameter for the creation of a virtual machine (VM) | Vm |
New notification message when more than one VM image shares the same VM name. |
|||
IN-13236 |
DGW-8161 | The SBC must provide additional control for the value of the Contact used in SIP dialogs. | Sbc |
Two new actions are available for SBC Call Agent rulesets:
|
|||
IN-13390 |
DGW-8108 | The warning message returned by the set command executed by the SnmpEx.Access.Command is interpreted as an error. | Snmp |
The SnmpEx.Access.Command (1.3.6.1.4.1.4935.1000.100.200.100.900.1.100.1.100.200.0) now interprets the warning message returned by an executed set command as a success. |
|||
--- | DGW-8090 | Add the possibility for the Vm service to convert an existing VM image from a file format to another (QCOW2 or RAW). | Vm |
|
|||
--- | DGW-8069 | Virtual machines (VM) should be properly shut down before restarting the Mediatrix unit. | Vm |
The new Vm.ShutdownTimeout parameter was added to configure the maximum amount of time allowed for a virtual machine to stop when the unit is restarted. |
|||
IN-13236 |
DGW-7942 | The Sbc service is removing parameters of the SIP Contact header, causing interoperability issues. | Sbc |
Three new actions are available for Sbc Call Agent Rulesets:
|
Incident # | CR # | Synopsis | Applies To |
---|---|---|---|
Description | |||
IN-13236 |
DGW-8444 | Unable to select the transport protocol in a Call Agent via the DGW Web page when a gateway is selected. | Sbc |
When a gateway is selected in a Call Agent, the configuration of the Force Transport parameter via the DGW Web page was disabled, now it is enabled. |
|||
IN-13236 |
DGW-8161 | The SBC must provide additional control for the value of the Contact used in SIP dialogs. | Sbc |
Two new SBC Call Agent Ruleset actions were added to provide a better control of the value of the Contact used in SIP dialogs
|
|||
IN-13390 |
DGW-8108 | The warning message returned by the set command executed by the SnmpEx.Access.Command is interpreted as an error. | Snmp |
The SnmpEx.Access.Command (1.3.6.1.4.1.4935.1000.100.200.100.900.1.100.1.100.200.0) was interpreting the warning message returned by an executed set command as an error. The warning message is now interpreted as a success and not an error, as it should. |
|||
IN-13236 |
DGW-7942 | The Sbc service is removing parameters of the SIP Contact header, causing interoperability issues. | Sbc |
The Sbc service was removing the parameters of the SIP Contact header.To allow greater control over SIP Contact parameters, new Sbc Call Agent Ruleset actions were added.The following new Call Agent Ruleset actions were added to control which Contact header parameters are relayed:
|
|||
IN-13114 |
DGW-7051 | T.38 fax negotiation through the SBC fails. | SBC |
T.38 negotiation failed because the INVITEs involved in T.38 represented media transport as UDPTL instead of udptl. Lowercase was corrected, and T.38 fax negotiation no longer fails. |
Incident # | CR # | Synopsis | Applies To |
---|
Copyright © 2019 Media5 Corporation.
This document contains information that is proprietary to Media5 Corporation.
Media5 Corporation reserves all rights to this document as well as to the Intellectual Property of the document and the technology and know-how that it includes and represents.
This publication cannot be reproduced, neither in whole nor in part, in any form whatsoever, without written prior approval by Media5 Corporation.
Media5 Corporation reserves the right to revise this publication and make changes at any time and without the obligation to notify any person and/or entity of such revisions and/or changes.